Curtis Instruments

 Preco Safety

 Printed Motor Works

Speed Controller - Permanent Magnet Motor Programmable 24v 110A 1228-2901

$ 379.50 each

+

Model 1228 Permanent Magnet Motor Speed Controller provide smooth and precise operating control, providing maximum user confidence. Model 1228 fully complies with European and US regulations and is fully programmable. Ideal for OEM applications on three or four wheeled mobility aids, such as scooters, and for light industrial equipment such as sweepers and scrubbers.

{tab=Features}

Features

  • Full bridge power MOSFET design provides infinitely variable forward, reverse, drive and brake control; silent high frequency and high efficiency operation.
  • Programmable through the Curtis Model 1311 or Model 1314 handheld programmer, an optional universal unit used for programming, testing and diagnostics.
  • Complete diagnostics also available through the status LED.
  • Fully compliant with all applicable international standards and TÜV requirements.
  • Available for wig-wag (center off) and single ended (speed pot and direction switch) throttles for both standard full stroke and restricted range 5kΩ potentiometers. Also accepts 0–5V throttle signals.
  • Throttle calibration mode aids the mechanical centering of the throttle using the 1311 Programmer to enter the mode. The horn will sound and the status LED will be off whenever the throttle is outside the neutral band.
  • MultiMode® input selects between two different operating modes. MultiMode® allows changes in speed, accel, decel, current limit, and IR compensation. This allows optimization of vehicle characteristics in each mode, for example indoor/outdoor.
  • Speed limit input provides additional variable speed limiting, in both mode ranges, with an external pot.
  • Linear acceleration and deceleration with softened response for smooth operation.
  • Current limited in both driving and regenerative braking.
  • Load compensation stabilizes speed on ramps and over obstacles. Compensates for battery voltage, voltage drops, and motor resistance.
  • High pedal disable (HPD) function monitors status of the throttle during turn on and prevents operation until the throttle has been returned to neutral.
  • Power off decel provides a controlled deceleration if the key switch is turned off while driving.
  • Comprehensive fault detect function monitors main contactor, output stage, throttle demand vs. output, etc.
  • Throttle fault circuitry shuts off controller if throttle signal goes out of range for any reason.
  • Missing brake detector forces neutral in the event of an open brake circuit (programmable).
  • Anti-rollback/roll forward circuitry sets brake delay according to speed and direction for improved braking response and minimized rollback on hills, etc.
  • Over-current protected brake driver protects the controller from shorts in the brake or its wiring. This low side output driver may also be programmed for side broom or brush contactor, hour meter, BDI enable, etc.
  • Brake PWM allows the brake driver to be programmed to a reduced holding voltage.
  • Reverse output drives a piezo beeper (customer supplied) in reverse.
  • "Push Too Fast" feature allows motor to coast with controller off and brake released. Pushing too fast automatically and safely shorts the motor to limit maximum coasting speed.
  • Push input electrically releases brake for key-on pushing (requires that the vehicle be stopped first).
  • Inhibit input disables the controller and puts the vehicle in a safe state during charging, etc.
  • Power saver deactivates the main relay after 25 seconds and entire controller after 25 minutes of non-operation.
  • Under voltage cutback function protects against low battery voltage.
  • Thermally protected and compensated for stable output and over-temperature protection.
  • Reverse polarity protected (battery input).

Model 1237 Only

  • SRO input sequencing options.
  • Emergency reverse (belly button) input causes immediate reversal.
  • Programmable high side driver output for brake light, belly button check, BDI enable, hourmeter, side broom contactor, etc.

{tab=Specifications}

S P E C I F I C A T I O N S

Curtis PMC Models

Nominal Battery

Current Limit

*1 Minute Rating

1 Hour Rating

Typ.  Voltage Drop @ 20A

Under Voltage Cutback

 

Voltage (V)

(Amps)

(Amps)

(Amps)

(V)

(V)

1227-21XX

24

150

150

60

0.16

16

1227-24XX

24

200

200

70

0.08

16

1227-27XX

24

250

250

100

0.04

16

1227-34XX

36

160

160

60

0.08

21

1227-41XX

48

100

100

40

0.15

27

1237-24XX

24

200

200

70

0.08

16

1237-34XX

36

160

160

60

0.08

21

1237-41XX

48

100

100

40

0.15

27

T Ü V  C o m p l i a n c e:

This Curtis product complies with the regulations of TÜV, the German service company which tests products and sets standards for product safety and quality. EMC compliance depends upon the installation and is the responsibility of the equipment manufacturer. Shielding may or may not be needed. When installed with the recommended shielding, the controller itself will meet TÜV EMC requirements. The deceleration adjustment must be set to meet all applicable TÜV braking distance requirements.

Model Number Description: 

Determine your model number by selecting the correct attribute for each item from the charts provided. Choose the appropriate letter that corresponds to the proper specification. Enter the code sequentially per the example below.

{tab=Dimensions}

DIMENSIONS:

Curtis Instruments - Speed Controller 1227

{/tabs}